|Author||Rick Kaseguma email@example.com|
|All Versions||0.0.3, 0.0.2, 0.0.1|
Particle port of Adafruit BlueFruitLE nRF51 Bluetooth LE library Provides bluetooth support to the Photon, Electron, etc. using the Adafruit BluefruitLE module. Works with both serial and SPI versions.
Device OS Version:
This table is generated from an automated build. Success only indicates that the code compiled successfully.
This content is provided by the library maintainer and has not been validated or approved.
A sample program is in firmware/examples/atcommand.ino. It allows you to type serial commands directly to the Bluefruit from the USB serial device.
This code works with the [Adafruit Bluefruit LE SPI Friend] (https://www.adafruit.com/products/2633).
For your own code, you will need to include these files:
#include "Adafruit_BLE/Adafruit_BLE.h" #include "Adafruit_BLE/Adafruit_BluefruitLE_SPI.h"
You’ll also need to create an object to interface with the Bluefruit and assign pins:
Adafruit_BluefruitLE_SPI ble(&SPI, BLUEFRUIT_SPI_CS, BLUEFRUIT_SPI_IRQ, BLUEFRUIT_SPI_RST);
Sample connections as configured in the atcommand.ino sample file:
- SCK - A3
- MISO - A5
- MOSI - A4
- CS - A2 (can use any pin)
- IRQ - D3 (can use any pin, does not use a hardware interrupt)
- RST - D2 (can use any pin)
- GND - GND
- VIN - 3V3
You can use the SPI1 hardware SPI port if you prefer.
The software can also be used with the [Adafruit Bluefruit LE UART Friend] (https://www.adafruit.com/products/2479).
#include "Adafruit_BLE/Adafruit_BLE.h" #include "Adafruit_BLE/Adafruit_BluefruitLE_UART.h"
// Optional, set to -1 her and leave MODE unconnected if not using #define BLUEFRUIT_UART_MODE_PIN -1 Adafruit_BluefruitLE_UART ble(&Serial1, BLUEFRUIT_UART_MODE_PIN);
- MOD - Optional for changing between modes (see note below)
- CTS - Must connect to GND!
- TXD - Connect to Photon/Electron RX pin
- RXI - Connect to Photon/Electron TX pin
- VIN - Connect to 3V3
- RTS - No connection
- GND - Connect to GND
- DFU - No connection
The Adafruit board has a switch that choose between CMD and UART mode. You can also control this through software by connecting the MOD pin to a output. Specify the pin wit
On the Particle Electron, you can also use Serial4 (TX=C3, RX=C2) or Serial5 (TX=C1, RX=C0).
Adafruit Project: [https://learn.adafruit.com/introducing-the-adafruit-bluefruit-spi-breakout/introduction] (https://learn.adafruit.com/introducing-the-adafruit-bluefruit-spi-breakout/introduction)
The latest version of this library for Particle here: [https://github.com/rickkas7/Adafruit_BLE] (https://github.com/rickkas7/Adafruit_BLE)
Original source including additional example programs (not ported): [https://github.com/adafruit/Adafruit_BluefruitLE_nRF51] (https://github.com/adafruit/Adafruit_BluefruitLE_nRF51)
Fork of the source for easy change merging is here: [https://github.com/rickkas7/Adafruit_BluefruitLE_nRF51] (https://github.com/rickkas7/Adafruit_BluefruitLE_nRF51)
Version 0.0.3 - Fixed compatibility with mesh devices (Argon, Boron, Xenon) due to redeclaration of err_t.