LSM6 accelerometer and gyro library This is a library for the Arduino IDE that helps interface with ST's LSM6DS33 accelerometer and gyro.
Device OS Version:
This table is generated from an automated build. Success only indicates that the code compiled successfully.
This content is provided by the library maintainer and has not been validated or approved.
Release date: 2016 January 19
This is a library for the Arduino IDE that helps interface with ST's LSM6DS33 3D accelerometer and gyro. The library makes it simple to configure the LSM6DS33 and read the raw accelerometer and gyro data through I²C.
This library is designed to work with the Arduino IDE versions 1.6.x or later; we have not tested it with earlier versions. This library should support any Arduino-compatible board, including the Pololu A-Star 32U4 controllers.
Make the following connections between the Arduino and the LSM6 board:
(including Arduino Uno, Leonardo, Mega; Pololu A-Star 32U4)
Arduino LSM6 board
5V - VIN GND - GND SDA - SDA SCL - SCL
(including Arduino Due)
Arduino LSM6 board
3V3 - VIN GND - GND SDA - SDA SCL - SCL
If you are using version 1.6.2 or later of the Arduino software (IDE), you can use the Library Manager to install this library:
- In the Arduino IDE, open the "Sketch" menu, select "Include Library", then "Manage Libraries...".
- Search for "LSM6".
- Click the LSM6 entry in the list.
- Click "Install".
If this does not work, you can manually install the library:
- Download the latest release archive from GitHub and decompress it.
- Rename the folder "lsm6-arduino-master" to "LSM6".
- Move the "LSM6" folder into the "libraries" directory inside your Arduino sketchbook directory. You can view your sketchbook location by opening the "File" menu and selecting "Preferences" in the Arduino IDE. If there is not already a "libraries" folder in that location, you should make the folder yourself.
- After installing the library, restart the Arduino IDE.
An example sketch is available that shows how to use the library. You can access it from the Arduino IDE by opening the "File" menu, selecting "Examples", and then selecting "LSM6". If you cannot find the example, the library was probably installed incorrectly and you should retry the installation instructions above.
The last values read from the accelerometer.
The last values read from the gyro.
The status of the last I²C write transmission. See the
Wire.endTransmission()documentation for return values.
bool init(deviceType device, sa0State sa0)
Initializes the library with the device being used (
device_auto) and the state of the SA0 pin (
sa0_auto), which determines the least significant bit of the I²C slave address. Constants for these arguments are defined in LSM6.h. Both of these arguments are optional; if they are not specified, the library will try to automatically detect the device address. A boolean is returned indicating whether the type of LSM6 device was successfully determined (if necessary).
Returns the device type specified to or detected by
Turns on the accelerometer and gyro and enables a consistent set of default settings.
This function will reset the accelerometer to ±2 g full scale and the gyro to ±245 dps. See the comments in LSM6.cpp for a full explanation of the settings.
void writeReg(uint8_t reg, uint8_t value)
Writes a sensor register with the given value.
Register address constants are defined by the regAddr enumeration type in LSM6.h.
uint8_t readReg(uint8_t reg)
Reads a sensor register and returns the value read.
Takes a reading from the accelerometer and stores the values in the vector
a. Conversion of the readings to units of g depends on the accelerometer's selected gain (full scale setting).
Takes a reading from the gyro and stores the values in the vector
g. Conversion of the readings to units of dps (degrees per second) depends on the gyro's selected gain (full scale setting).
Takes a reading from both the accelerometer and gyro and stores the values in the vectors
void setTimeout(uint16_t timeout)
Sets a timeout period in milliseconds after which the read functions will abort if the sensor is not ready. A value of 0 disables the timeout.
Returns the current timeout period setting.
Indicates whether a read timeout has occurred since the last call to
- 1.0.0 (2016 Jan 19): Original release.