Mesh Accessories

Grove Starter Kit for Particle Mesh

The Grove starter kit is designed to make your first exploration into the world of sensing and actuating a breeze. The kit comes with seven different components that work out-of-the-box with Particle Mesh hardware and let you focus on learning the basics. Working with Starter Kit requires no soldering and minimal wiring. Simply connect the kit’s Grove Shield (the new co-developed FeatherWing adapter from Particle and SeeedStudio) to your Particle Mesh board and use the included cables to connect the adapter and the sensors and actuators that you want to use. It’s a plug-and-play experience.

Kit Contents

  • 1x Grove Shield for Particle Mesh
  • 1x Button
  • 1x Rotary Angle Sensor
  • 1x Ultrasonic Ranger
  • 1x Temp&Humi Sensor
  • 1x Light Sensor v1.2
  • 1x Chainable RGB LED
  • 1x Buzzer
  • 1x 4-Digit Display

Grove shield

The main shield consists of a connector to plug in any of the Particle Mesh dev kit and a set of 8 grove ports for plugging in various grove accessories. The ports consist of:

  • 3 Digital ports
  • 2 Analog ports
  • 2 I2C ports
  • 1 UART port

The pins on the Grove connector are as follows:

Pin Color Digital Analog I2C UART
1 Yellow Primary I/O Primary Analog In I2C Clock Serial RX
2 White Secondary I/O Secondary Analog In I2C Data Serial TX
3 Red Power Power Power Power
4 Black GND GND GND GND

Button

Button is a momentary push button. It contains one independent "momentary on/off" button. “Momentary” means that the button rebounds on its own after it is released. The button outputs a HIGH signal when pressed, and LOW when released. The Sig marked on silk layer stands for signal while NC is not connected to anything.

It can be used on either a digital or analog input port, and the button is read using the primary digital I/O using the digitalRead function. The digitalRead function can be used on both digital and analog pins.

Additional information available here.

Rotary Angle Sensor

The rotary angle sensor produces analog output between 0 and Vcc (3.3VDC) on its D1 connector. The D2 connector is not used. The angular range is 300 degrees with a linear change in value. The resistance value is 10k ohms. This essentially is a potentiometer.

It must be used on an analog input port, and the value is read using the primary analog input using the analogRead function.

Additional information available here.

Ultrasonic Ranger

Ultrasonic ranger is a non-contact distance measurement module which works at 40KHz. When we provide a pulse trigger signal with more than 10uS through signal pin, the sensor will issue 8 cycles of 40kHz cycle level and detect the echo. The pulse width of the echo signal is proportional to the measured distance. Here is the formula: Distance = echo signal high time * Sound speed (340M/S)/2. The sensor's trig and echo signal share 1 SIG pin.

The library is available in the Web IDE as Grove_Ultrasonic_Ranger.

Additional information available here.

Temperature and Humidity Sensor

This Temperature and Humidity sensor provides a pre-calibrated digital output. A unique capacitive sensor element measures relative humidity and the temperature is measured by a negative temperature coefficient (NTC) thermistor. It has excellent reliability and long term stability. Please note that this sensor will not work for temperatures below 0 degrees. It uses the DHT-11 sensor.

The library is available in the Web IDE as Grove_Temperature_And_Humidity_Sensor.

Additional information available here.

Light Sensor v1.2

Light sensor integrates a photo-resistor (light dependent resistor) to detect the intensity of light. The resistance of photo-resistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value). The output signal is analog value, the brighter the light is, the larger the value.

It must be used on an analog input port, and the value is read using the primary analog input using the analogRead function.

This module can be used to build a light controlled switch i.e. switch off lights during day time and switch on lights during night time.

Additional information available here.

Chainable RGB LED

Chainable RGB LED is based on P9813 chip which is a full-color LED driver. It provides 3 constant-current drivers as well as modulated output of 256 shades of gray. It communicates with a MCU using 2-wire transmission (Data and Clock). This 2-wire transmission can be used to cascade additional Grove - Chainable RGB LED modules. The built-in clock regeneration enhances the transmission distance. This Grove module is suitable for any colorful LED based projects.

The library is available in the Web IDE as Grove_ChainableLED.

Additional information available here.

Buzzer

Buzzer module has a piezo buzzer as the main component. The piezo can be connected to digital outputs, and will emit a tone when the output is HIGH. Alternatively, it can be connected to an pulse-width modulation output to generate various tones and effects.

You can use the pinMode and digitalWrite functions to control the output.

pinMode(D2, OUTPUT);
digitalWrite(D2, HIGH);
delay(1000);
digitalWrite(D2, LOW);

It can be used on a digital or analog port, as the analog inputs can also be used as digital outputs.

An example using tone (PWM) to play a melody can be found here. Not every pin is PWM compatible, so make sure you use a port that supports PWM.

Additional information available here.

4-Digit Display

This is a 4 digit seven-segment display module that uses TM1637 driver chip. This driver is controlled with a two wire interface (CLK, DATA). This is perfect for displaying 4 digit numeric values.

The library is available in the Web IDE as Grove_4Digit_Display.

Additional information available here.

Adafruit FeatherWing OLED Display 128x32

Adafruit FeatherWing OLED Display

The Adafruit OLED display FeatherWing makes it easy to add a small text and graphics display to your project. Built in a FeatherWing form-factor, you can use a FeatherWing Doubler or FeatherWing Tripler to add a display to your Argon, Boron, or Xenon project with no loose wires. And it includes three handy momentary push-buttons.

You can purchase one from the Particle Store or from Adafruit. You can find more technical information at Adafruit.

The library is available in the Web IDE as oled-wing-adafruit. You can find additional documentation here.

The display is a SSD1306 and connects by I2C (pins D0 and D1).

The three buttons are:

Button Pin Notes
A D4 No pull-up. Can't be used with Ethernet.
B D3 100K pull-up. Can't be used with Ethernet.
C D2 No pull-up.

The library takes care of setting the appropriate input modes and debouncing the buttons for you.

Note that if you are using the Adafruit OLED display and the Particle Ethernet FeatherWing, you cannot use buttons A or B as those pins are used by Ethernet.

Ethernet FeatherWing

The Ethernet FeatherWing is the fastest way to add wired connectivity to your Argon, Boron, or Xenon and turns any Particle Mesh developer kit into an Ethernet gateway. Based on the WIZnet W5500 chip, this side-by-side FeatherWing maintains great RF performance even while adding Ethernet connectivity to any Particle Mesh device.

The form-factor is based around the Adafruit FeatherWing Tripler. The two side connectors allow you to plug in one Particle Mesh device along with a Feather accessory.

Pin Map

Mesh Pin Ethernet FeatherWing Pin
MISO SPI MISO
MOSI SPI MOSI
SCK SPI SCK
D3 nRESET[1]
D4 nINTERRUPT[1]
D5 nCHIP SELECT[1]

Notes:

[1] These pins are connected via jumper pads on the bottom. You can cut these jumper traces and rewire them to a different pin on the Mesh device if the need arises.

The Ethernet driver for this wing is baked into the Mesh Device OS. When you set up a new Particle Mesh device that is plugged into an Ethernet FeatherWing, simply select the USE WITH ETHERNET? option on your Particle mobile app and it should recognize and talk over Ethernet automagically. It's that simple.

The hardware design for this wing is completely opensource. All the files are available on our GitHub repository here.

If you are using the Adafruit Ethernet Feather Wing, be sure to connect the nRESET and nINTERRUPT pins (on the small header on the short side) to pins D3 and D4 with jumper wires. These are required for proper operation.

Classic Adapter

The Particle Classic Adapter lets you use your Asset Tracker, Relay Shield, or other third-party shields with our third generation developer kits. Plug your Argon, Boron, or Xenon into this adapter and continue development as usual!

The top of the adapter has female connectors for you to plug in the Particle Mesh device. The bottom has male header pins in the Particle legacy form-factor for devices such as the Electron, Photon, or the Core.

Note: This product is a one-way adapter. That is, this product does not enable use of Adafruit FeatherWings with the Photon or Electron.

Pin Map

Legacy Device Mesh Device
A0 A0
A1 A1
A2 A2
A3 A3
A4 A4
A5 A5
D0 D0
D1 D1
D2 D2
D3 D3
D4 D4
D5 D5
D6 D6
D7 D7
C5[1] D8
TX TX
RX RX
B5[1] D11
WKP[1] D12
DAC[1] D13
RST RST
VIN VUSB
3V3 3V3

Notes:

[1] These pins are connected via jumper pads on the top. You can cut these jumper traces and rewire them to a different pin on the Mesh device if the need arises.

[2] Pins C0 to C4 and B0 to B4 on the Particle legacy device headers are not connected to anything.

[3] Pins MD, Li+, and EN on the Particle Mesh device are not connected to anything.

Debugger

The Particle Debugger gives you the power of professional debugging at a fraction of the cost. Using this accessory, you’ll be able to program Particle mesh-ready hardware over common interfaces like JTAG and SWD, using open source tools like GDB and openocd.

Supports the open source CMSIS-DAP specification and DAPLink firmware developed by ARM. On Mac, Linux, and Windows it requires no additional device drivers.

It also provides a USB to TTL serial port. This requires no device drivers on Mac, Linux, or Windows 10 or later, but you may need to install a device driver for earlier versions of Windows to use the serial port feature.

Comes with one JTAG ribbon cable.

For more information about debugging see the JTAG FAQ. Future version of Particle Workbench will support the Particle Debugger as well.

Debugging mesh devices

Connecting a Argon, Boron, or Xenon to the debugger is as easy as connecting the included ribbon cable, as pictured below. It's keyed so it will only go in one way. The devices ship with a small plastic protective plug in the debugging connector; make sure you remove that first.

Debugger

Debugging legacy platforms

Using the headers on the Particle Debugger you can attach it to other ARM processor devices like the STM32 in the Particle Photon, P1, Electron, and E Series for SWD (serial wire debug).

With the debugger positioned like this, USB connector toward you and the headers facing up:

Debugger

Left Header Right Header
VDD SWCLK
RTS SWDIO
RX NC
TX NC
CTS GND
GND VUSB

In order to use SWD debugging you need to connect:

  • D7: SWDIO
  • D6: SWCLK
  • GND

FeatherWing Tripler

Perfect for any prototyping project, the Tripler provides space to add-on up to two FeatherWing accessories without any stacking header needs. Compatible with the newest generation of Particle developer kits (Particle Mesh).

The Tripler has three breakouts for each pin on a Feather, as well as plain grid proto holes. In addition, three sets of pins are cross connected with a full strip of connected pads for GND and 3.3V.