The Argon is a powerful Wi-Fi enabled development board for Wi-Fi networks. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes.
The Argon is great for connecting existing projects to the Particle Device Cloud over a Wi-Fi network.
- Espressif ESP32-D0WD 2.4 GHz Wi-Fi coprocessor
- On-board 4MB flash for ESP32
- 802.11 b/g/n support
- 802.11 n (2.4 GHz), up to 150 Mbps
- Nordic Semiconductor nRF52840 SoC
- ARM Cortex-M4F 32-bit processor @ 64MHz
- 1MB flash, 256KB RAM
- Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps
- Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations
- ARM TrustZone CryptoCell-310 Cryptographic and security module
- Up to +8 dBm TX power (down to -20 dBm in 4 dB steps)
- NFC-A tag
- On-board additional 4MB SPI flash
- 20 mixed signal GPIO (6 x Analog, 8 x PWM), UART, I2C, SPI
- Micro USB 2.0 full speed (12 Mbps)
- Integrated Li-Po charging and battery connector
- JTAG (SWD) Connector
- RGB status LED
- Reset and Mode buttons
- On-board PCB antenna
- U.FL connector for external antenna
- Meets the Adafruit Feather specification in dimensions and pinout
- FCC, CE and IC certified
- RoHS compliant (lead-free)
The USB port is the easiest way to power up the Argon. Please make sure that the USB port is able to provide at least 500mA. Power from the USB is regulated down to 3.3V by the on board Torex XC9258A step-down regulator.
The pin is internally connected to the VBUS of the USB port. The nominal output should be around 4.5 to 5 VDC when the device is plugged into the USB port and 0 when not connected to a USB source. You can use this pin to power peripherals that operate at such voltages. Do not exceed the current rating of the USB port, which is nominally rated to 500mA. This pin is also protected with an internal fuse rated at 1000mA.
If you want to make your projects truly wireless, you can power the device with a single cell LiPo (3.7V). The Argon has an on board LiPo charger that will charge and power the device when USB source is plugged in or power the device from the LiPo alone in the absence of the USB.
NOTE: Please pay attention to the polarity of the LiPo connector. Not all LiPo batteries follow the same polarity convention!
This pin is internally connected to the positive terminal of the LiPo connector. You can connect a single cell LiPo/Lithium Ion or a DC supply source to this pin for powering the Argon. Remember that the input voltage range on this pin is 3.6 to 4.2 VDC.
This pin is the output of the on board 3.3V step-down switching regulator (Torex XC9258A). The regulator is rated at 1000mA max. When using this pin to power other devices or peripherals remember to budget in the current requirement of the Argon first. This pin can also be used to power the Argon in absence of the USB or LiPo power. When powering over this pin, please connect the ENABLE pin to GND so that the on board regulator is disabled.
The EN pin is not a power pin, per se, but it controls the 3V3 power. The EN pin is pulled high by a 100K resistor to the higher of VUSB, the micro USB connector, or Li+. Because the pull-up can result in voltages near 5V you should never directly connect EN to a 3.3V GPIO pin. Instead, you should only pull EN low, such as by using an N-channel MOSFET or other open-collector transistor.
The EN pin can force the device into a deep power-down state where it uses very little power. It also can used to assure that the device is completely reset, similar to unplugging it, with one caveat:
If using the EN pin to deeply reset the device, you must be careful not to allow leakage current back into the nRF52 MCU by GPIO or by pull-ups to 3V3. If you only power external devices by 3V3 you won't run into this, as 3V3 is de-powered when EN is low.
However, if you have circuitry that is powered by a separate, external power supply, you must be careful. An externally powered circuit that drives a nRF52 GPIO high when EN is low can provide enough current to keep the nRF52 from powering down and resetting. Likewise, a pull-up to an external power supply can do the same thing. Be sure that in no circumstances can power by supplied to the nRF52 when 3V3 is de-powered.
See the power supply schematic, below, for more information.
There are two radios on the Argon. A BLE radio (nRF52840) and a WiFi radio (ESP32). For the WiFi radio, we have provided a u.FL connector to plug in the WiFi antenna. This is required if you wish to use the WiFi connectivity.
There are two options for the BLE antenna on the Argon. It comes with an on-board PCB antenna which is selected by default in the device OS and a u.FL connector if you wish to connect an external antenna. If you wish to use the external antenna, you'll need to issue an appropriate command in the firmware.
BLE and WiFi
The Argon includes one of these antennas, but a second for use with BLE can be purchased in the Particle online store.
|Particle Device||Frequency||Antenna Type||Manufacturer||MFG. Part #||Gain|
|Argon||2400-2500 MHz||PCB Antenna||Particle||ANT-FLXV2||2.0dBi peak|
It is also possible to use most antennas designed for Wi-Fi (2.4 GHz) as a BLE antenna. In some cases, a u.FL to RP-SMA adapter will be required. If you are building a product using alternative antennas, additional certification may be required.
|Peripheral Type||Qty||Input(I) / Output(O)|
Note: All GPIOs are only rated at 3.3VDC max.
The Argon has a dedicated 10 pin debug connector that exposes the SWD interface of the nRF5280. This interface can be used to debug your code or reprogram your Argon bootloader, device OS, or the user firmware using any standard SWD tools including our Gen 3 Debugger.
- Bootloader (48KB, @0xF4000)
- User Application
- 256KB @ 0xB4000 (Device OS 3.1 and later)
- 128KB @ 0xD4000 (Device OS 3.0 and earlier)
- System (656KB, @0x30000)
- SoftDevice (192KB)
- OTA (1500KB, @0x00289000)
- Reserved (420KB, @0x00220000)
- FAC (128KB, @0x00200000)
- LittleFS (2M, @0x00000000)
You can download a high resolution PDF version of the pin out here.
|Li+||This pin is internally connected to the positive terminal of the LiPo battery connector.|
|VUSB||This pin is internally connected to the USB (+ve) supply.|
|3V3||This pin is the output of the on-board 3.3V regulator.|
|GND||System ground pin.|
|EN||Device enable pin is internally pulled-up. To disable the device, connect this pin to GND.|
|RST||Active-low system reset input. This pin is internally pulled-up.|
|MD||This pin is internally connected to the MODE button. The MODE function is active-low.|
|RX||Primarily used as UART RX, but can also be used as a digital GPIO.|
|TX||Primarily used as UART TX, but can also be used as a digital GPIO.|
|SDA||Primarily used as data pin for I2C, but can also be used as a digital GPIO.|
|SCL||Primarily used as clock pin for I2C, but can also be used as a digital GPIO.|
|MO,MI,SCK||These are the SPI interface pins, but can also be used as a digital GPIO.|
|D2-D8||These are generic GPIO pins. D2-D8 are PWM-able.|
|A0-A5||These are analog input pins that can also act as standard digital GPIO. A0-A5 are PWM-able.|
For a detailed explanation of different color codes of the RGB system LED, please take a look here.
|ON||Charging in progress|
|Supply Input Voltage||VIN-MAX||+6.2||V|
|Battery Input Voltage||VLiPo||+6.5||V|
|Supply Output Current||I3V3-MAX-L||1000||mA|
|ESD Susceptibility HBM (Human Body Mode)||VESD||2||kV|
 Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
|LiPo Battery Voltage||VLiPo||+3.3||+4.4||V|
|Supply Input Voltage||V3V3||+3.0||+3.3||+3.6||V|
|Supply Output Voltage||V3V3||+3.3||V|
|Humidity Range Non condensing, relative humidity||95||%|
|Operating Current (uC on, peripherals and radio disabled)||Iidle||3.1||3.52||3.58||mA|
|Operating Current (uC on, radio connected but idle)||Iwifi_cloud_idle||20.5||25.8||219||mA|
|Operating Current (uC on, radio connected and transmitting)||Iwifi_cloud_tx||20.1||31.7||261||mA|
|STOP mode sleep, GPIO wake-up||Istop_gpio||350||396||459||uA|
|STOP mode sleep, analog wake-up||Istop_analog||349||398||456||uA|
|STOP mode sleep, RTC wake-up||Istop_intrtc||340||398||461||uA|
|STOP mode sleep, BLE wake-up, advertising||Istop_ble_adv||340||442||3420||uA|
|STOP mode sleep, BLE wake-up, connected||Istop_ble_conn||102||435||1970||uA|
|STOP mode sleep, serial wake-up||Istop_usart||348||397||449||uA|
|STOP mode sleep, Wi-Fi wake-up||Istop_wifi||15.3||22.2||110||mA|
|ULP mode sleep, GPIO wake-up||Iulp_gpio||81.7||169||uA|
|ULP mode sleep, analog wake-up||Iulp_analog||81.1||174||uA|
|ULP mode sleep, RTC wake-up||Iulp_intrtc||80.7||168||uA|
|ULP mode sleep, BLE wake-up, advertising||Iulp_ble_adv||141||3280||uA|
|ULP mode sleep, BLE wake-up, connected||Iulp_ble_conn||138||1870||uA|
|ULP mode sleep, serial wake-up||Iulp_usart||476||520||569||uA|
|ULP mode sleep, Wi-Fi wake-up||Iulp_wifi||16.3||21.3||105||mA|
|HIBERNATE mode sleep, GPIO wake-up||Ihib_gpio||64.7||161||uA|
|HIBERNATE mode sleep, analog wake-up||Ihib_analog||65.0||159||uA|
|Power disabled (EN pin = LOW)||Idisable||20||30||uA|
1The min, and particularly peak, values may consist of very short transients. The typical (typ) values are the best indicator of overall power consumption over time. The peak values indicate the absolute minimum capacity of the power supply necessary, not overall consumption.
Argon has two radio modules.
Nordic Semiconductor nRF52840 SoC for BLE and NFC.
|Operating Frequencies||2360 to 2500 MHz|
|Output Power||Programmable -20dBm to +8dBm|
|PLL channel spacing||1 MHz|
|On the air data rate||125 to 2000 kbps|
Espressif Systems ESP32 for WiFi
|WLAN Standards||IEEE 802 11b/g/n|
|Antenna Port||Single Antenna|
|Frequency Band||2412 to 2484 MHz|
Note: Bluetooth features of the ESP32 are not exposed.
These specifications are based on the nRF52840 datasheet.
|Input high voltage||VIH||0.7*3.3||--||3.3||V|
|Input low voltage||VIL||0||0.3*3.3||V|
|Current at GND+0.4 V, output set low, high drive||IOL,HDL||V3V3 >= 2.7V||6||10||15||mA|
|Current at V3V3-0.4 V, output set high, high drive||IOH,HDH||V3V3 >= 2.7V||6||9||14||mA|
|Current at GND+0.4 V, output set low, standard drive||IOL,SD||V3V3 >= 2.7V||1||2||4||mA|
|Current at V3V3-0.4 V, output set high, standard drive||IOH,SD||V3V3 >= 2.7V||1||2||4||mA|
GPIO default to standard drive (2mA) but can be reconfigured to high drive (9mA) in Device OS 2.0.0 and later using the
- Weight = 10 grams
The Argon uses two single row 0.1" pitch male header pins. One of them is 16 pin while the other is 12 pin. It can be mounted with matching 0.1" pitch female headers with a typical height of 0.335" (8.5mm). When you search for parts like these it can be difficult to navigate the thousands of parts available online so here are a few good choices for the Argon:
|Description||MFG||MFG Part Number|
|16-pin 0.1" (2.54mm) Female Header||Sullins||PPTC161LFBN-RC|
|16-pin 0.1" (2.54mm) Female Header||TE||6-535541-4|
|12-pin 0.1" (2.54mm) Female Header||Sullins||PPTC121LFBN-RC|
|12-pin 0.1" (2.54mm) Female Header||TE||6-534237-0|
The Argon can be directly soldered onto the PCB or be mounted with the above mentioned female headers.
The complete schematic and board files are open source and available on Particle's GitHub repository here.
Argon are available from store.particle.io in single quantities.
|ARG-AQKT||Argon Air Quality Monitor Kit [x1]||Global||GA|
|ARG-STRTKT||Argon Starter Kit [x1]||Global||GA|
|ARGNKIT||Argon, Starter Kit [x1]||Global||GA|
|ARGNTRAY50||Argon, Tray [x50]||Global||GA|
- Model Number: ARGN
- FCC ID: 2AEMI-ARGN
- IC: 20127-ARGN
The Argon contains highly sensitive electronic circuitry and is an Electrostatic Sensitive Device (ESD). Handling Argon without proper ESD protection may destroy or damage it permanently. Proper ESD handling and packaging procedures must be applied throughout the processing, handling and operation of any application that incorporates Argon. ESD precautions should be implemented on the application board where the Argon is mounted. Failure to observe these precautions can result in severe damage to the Argon!
There are four connectors on the Argon that will get damaged with improper usage. The JST connector on the circuit board, where you plug in the LiPo battery, is very durable but the connector on the battery itself is not. When unplugging the battery, take extra precaution to NOT pull the connector using the wires, but instead hold the plug at its base to avoid putting stress on the wires. This can be tricky with bare hands - needle nose pliers are your friend here.
The micro B USB connector on the Argon is soldered on the PCB with large surface pads as well as couple of through hole anchor points. Despite this reinforcement, it is very easy to rip out the connector if too much stress is put on in the vertical direction.
The U.FL antenna connector is not designed to be constantly plugged and unplugged. The antenna pin is static sensitive and you can destroy the radio with improper handling. A tiny dab of glue (epoxy, rubber cement, liquid tape or hot glue) on the connector can be used to securely hold the plug in place.
The 10 pin SWD connector provides an easy in-system debugging access to the device. The pins on the connector can easily be damaged if the mating connector cable is inserted improperly. If you are trying to debug the device, you probably are already not in a good mood. The last thing you want is to render the connector useless. Be nice and be gentle with the connector. Good luck with the debugging!
The breadboard provided with the Argon is specifically designed to require low insertion force. This makes it easy to plug the Argon in and out of the breadboard. If you end up using a different breadboard, remember that it may require more force. In this case, always remember to pinch-hold your precious Argon by the sides (along the header pins) when plugging-unplugging and not by the USB connector (don't be this person).
The Argon comes preprogrammed with a bootloader and a user application called Tinker. This application works with an iOS and Android app also named Tinker that allows you to very easily toggle digital pins, take analog and digital readings and drive variable PWM outputs.
The bootloader allows you to easily update the user application via several different methods, USB, OTA, Serial Y-Modem, and also internally via the Factory Reset procedure. All of these methods have multiple tools associated with them as well.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling The final end product must be labeled in a visible area with the following:
- Contains FCC ID: 2AEMI-ARGN
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
- l’appareil ne doit pas produire de brouillage;
- l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Caution Exposure: This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance. Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section 2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect.
The final end product must be labelled in a visible area with the following: The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows:
- Contains transmitter module IC: 20127-ARGN
This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
The end user manual shall include all required regulatory information/warning as shown in this manual.
|v001||2018 Oct 26||MB||Initial release|
|v002||2020 Jan 21||RK||Remove mesh|
|v003||2020 Sep 01||RK||Add EN pin information|
|v004||16-Sep-2020||RK||Added power consumption information|
|v005||15-Mar-2021||RK||Updated ordering information|
|v006||28-Jun-2021||RK||Added Device OS 3.1 memory map information|
|v007||28-Jul-2021||RK||Corrected number of SPI ports (2) in peripherals and GPIO|
|v008||10-Sep-2021||RK||Changed wording of peak vs. max current|